mirror of
https://github.com/fsender/readguy.git
synced 2025-12-12 21:08:14 +08:00
1.3.3: fix 2.66BWR refresh & pre-add new driver
This commit is contained in:
fsender
214
src/readguy.cpp
214
src/readguy.cpp
@@ -38,6 +38,36 @@ int8_t ReadguyDriver::pin_cmx=-1;
|
||||
const PROGMEM char ReadguyDriver::projname[8] = "readguy";
|
||||
const PROGMEM char ReadguyDriver::tagname[7] = "hwconf";
|
||||
volatile uint8_t ReadguyDriver::spibz=0;
|
||||
#ifndef DYNAMIC_PIN_SETTINGS
|
||||
const int8_t ReadguyDriver::config_data[22] = {
|
||||
127 , //READGUY_cali
|
||||
READGUY_shareSpi ,
|
||||
READGUY_epd_type ,// 对应的epd驱动程序代号, -1为未指定
|
||||
//显示驱动部分, 显示默认使用vspi (vspi也是默认SPI库的通道)
|
||||
READGUY_epd_mosi ,// 目标显示器的 MOSI 引脚
|
||||
READGUY_epd_sclk ,// 目标显示器的 SCLK 引脚
|
||||
READGUY_epd_cs ,// 目标显示器的 CS 引脚
|
||||
READGUY_epd_dc ,// 目标显示器的 DC 引脚
|
||||
READGUY_epd_rst ,// 目标显示器的 RST 引脚
|
||||
READGUY_epd_busy ,// 目标显示器的 BUSY 引脚
|
||||
//sd卡驱动部分, 默认使用hspi (sd卡建议用hspi)
|
||||
READGUY_sd_miso ,// 目标sd卡的 MISO 引脚, sd_share_spi == 1 时无效
|
||||
READGUY_sd_mosi ,// 目标sd卡的 MOSI 引脚, sd_share_spi == 1 时无效
|
||||
READGUY_sd_sclk ,// 目标sd卡的 SCLK 引脚, sd_share_spi == 1 时无效
|
||||
READGUY_sd_cs ,// 目标sd卡的 CS 引脚.
|
||||
READGUY_i2c_sda ,// 目标i2c总线的SDA引脚, 当且仅当启用i2c总线时才生效
|
||||
READGUY_i2c_scl ,// 目标i2c总线的SCL引脚, 当且仅当启用i2c总线时才生效
|
||||
//按键驱动部分, 为负代表高触发, 否则低触发,
|
||||
//注意, 这里的io编号是加1的, 即 1或-1 代表 gpio0 的低触发/高触发
|
||||
READGUY_btn1 ,
|
||||
READGUY_btn2 ,
|
||||
READGUY_btn3 ,
|
||||
READGUY_bl_pin ,//前置光接口引脚IO
|
||||
READGUY_rtc_type ,//使用的RTC型号(待定, 还没用上)
|
||||
0 ,//READGUY_sd_ok SD卡已经成功初始化
|
||||
0 //READGUY_buttons 按钮个数, 0-3都有可能
|
||||
};
|
||||
#endif
|
||||
#ifndef ESP8266
|
||||
SPIClass *ReadguyDriver::sd_spi =nullptr;
|
||||
SPIClass *ReadguyDriver::epd_spi=nullptr;
|
||||
@@ -85,10 +115,15 @@ uint8_t ReadguyDriver::init(uint8_t WiFiSet, bool initepd){
|
||||
#endif
|
||||
nvs_deinit();
|
||||
#else
|
||||
nvs_init();
|
||||
if(checkEpdDriver()!=127) setEpdDriver(initepd/* ,g_width,g_height */); //初始化屏幕
|
||||
else for(;;); //此处可能添加程序rollback等功能操作(比如返回加载上一个程序)
|
||||
setSDcardDriver();
|
||||
setButtonDriver();
|
||||
if(!nvs_read()){
|
||||
nvs_write(); //全部成功之后, 写入引脚信息到NVS.
|
||||
}
|
||||
nvs_deinit();
|
||||
#endif
|
||||
Serial.println(F("[Guy init] init done."));
|
||||
READGUY_cali=127;
|
||||
@@ -111,47 +146,124 @@ uint8_t ReadguyDriver::checkEpdDriver(){
|
||||
#endif
|
||||
if(guy_dev != nullptr && READGUY_epd_type!=guy_dev->drv_ID()) delete guy_dev; //释放多余的内存
|
||||
//Serial.printf("initing epd %s...\n",epd_drivers_list[READGUY_epd_type]);
|
||||
#ifdef DYNAMIC_PIN_SETTINGS
|
||||
switch (READGUY_epd_type){
|
||||
#ifdef READGUY_DEV_154A
|
||||
case READGUY_DEV_154A: guy_dev = new guydev_154A_290A ::dev154A; break; //适用于一般的价签黑白屏
|
||||
case READGUY_DEV_154A: guy_dev = new guydev_154A_290A ::dev154A; break; //适用于一般的价签黑白屏
|
||||
#endif
|
||||
#ifdef READGUY_DEV_154B
|
||||
case READGUY_DEV_154B: guy_dev = new guydev_154B_270B_290B ::dev154B; break; //适用于
|
||||
case READGUY_DEV_154B: guy_dev = new guydev_154B_270B_290B ::dev154B; break; //适用于
|
||||
#endif
|
||||
#ifdef READGUY_DEV_213A
|
||||
case READGUY_DEV_213A: guy_dev = new guydev_213A ::drv; break;
|
||||
case READGUY_DEV_213A: guy_dev = new guydev_213A ::drv; break;
|
||||
#endif
|
||||
#ifdef READGUY_DEV_266A
|
||||
case READGUY_DEV_266A: guy_dev = new guydev_213B_266A ::dev266A; break;
|
||||
case READGUY_DEV_266A: guy_dev = new guydev_213B_266A ::dev266A; break;
|
||||
#endif
|
||||
#ifdef READGUY_DEV_213B
|
||||
case READGUY_DEV_213B: guy_dev = new guydev_213B_266A ::dev213B; break;
|
||||
case READGUY_DEV_213B: guy_dev = new guydev_213B_266A ::dev213B; break;
|
||||
#endif
|
||||
#ifdef READGUY_DEV_290A
|
||||
case READGUY_DEV_290A: guy_dev = new guydev_154A_290A ::dev290A; break;
|
||||
case READGUY_DEV_290A: guy_dev = new guydev_154A_290A ::dev290A; break;
|
||||
#endif
|
||||
#ifdef READGUY_DEV_290B
|
||||
case READGUY_DEV_290B: guy_dev = new guydev_154B_270B_290B ::dev290B; break;
|
||||
case READGUY_DEV_290B: guy_dev = new guydev_154B_270B_290B ::dev290B; break;
|
||||
#endif
|
||||
#ifdef READGUY_DEV_420A
|
||||
case READGUY_DEV_420A: guy_dev = new guydev_420A ::drv; break;
|
||||
case READGUY_DEV_420A: guy_dev = new guydev_420A ::drv; break;
|
||||
#endif
|
||||
#ifdef READGUY_DEV_420B
|
||||
case READGUY_DEV_420B: guy_dev = new guydev_420B ::drv; break;
|
||||
case READGUY_DEV_420B: guy_dev = new guydev_420B ::drv; break;
|
||||
#endif
|
||||
#ifdef READGUY_DEV_370A
|
||||
case READGUY_DEV_370A: guy_dev = new guydev_370A ::drv; break;
|
||||
case READGUY_DEV_370A: guy_dev = new guydev_370A ::drv; break;
|
||||
#endif
|
||||
#ifdef MEPD_DEBUG_DISPLAY
|
||||
case MEPD_DEBUG_DISPLAY:guy_dev = new EpdLcdDebug ::drv; break;
|
||||
case MEPD_DEBUG_DISPLAY: guy_dev = new EpdLcdDebug ::drv; break;
|
||||
#endif
|
||||
#ifdef READGUY_DEV_270B
|
||||
case READGUY_DEV_270B: guy_dev = new guydev_154B_270B_290B ::dev270B; break;
|
||||
case READGUY_DEV_270B: guy_dev = new guydev_154B_270B_290B ::dev270B; break;
|
||||
#endif
|
||||
#ifdef READGUY_DEV_213B3C
|
||||
case READGUY_DEV_213B3C: guy_dev = new guydev_213B_266A ::dev213B3C; break;
|
||||
#endif
|
||||
#ifdef READGUY_DEV_266A3C
|
||||
case READGUY_DEV_266A3C: guy_dev = new guydev_213B_266A ::dev266A3C; break;
|
||||
#endif
|
||||
|
||||
#ifdef READGUY_DEV_154C
|
||||
case READGUY_DEV_154C: guy_dev = new guydev_154C ::drv; break;
|
||||
#endif
|
||||
#ifdef READGUY_DEV_370B
|
||||
case READGUY_DEV_370B: guy_dev = new guydev_370B ::drv; break;
|
||||
#endif
|
||||
#ifdef READGUY_DEV_426A
|
||||
case READGUY_DEV_426A: guy_dev = new guydev_426A ::drv; break;
|
||||
#endif
|
||||
#ifdef READGUY_DEV_583A
|
||||
case READGUY_DEV_583A: guy_dev = new guydev_583A ::drv; break;
|
||||
#endif
|
||||
#ifdef READGUY_DEV_583B
|
||||
case READGUY_DEV_583B: guy_dev = new guydev_583B ::drv; break;
|
||||
#endif
|
||||
#ifdef READGUY_DEV_750A
|
||||
case READGUY_DEV_750A: guy_dev = new guydev_750A ::drv; break;
|
||||
#endif
|
||||
#ifdef READGUY_DEV_1020A
|
||||
case READGUY_DEV_1020A: guy_dev = new guydev_1020A ::drv; break;
|
||||
#endif
|
||||
//添加新屏幕型号 add displays here
|
||||
default:
|
||||
Serial.println(F("[GUY ERR] EPD DRIVER IC NOT SUPPORTED!\n"));
|
||||
return 127;
|
||||
}
|
||||
#else
|
||||
#if (defined(READGUY_DEV_154A) && (READGUY_epd_type==READGUY_DEV_154A))
|
||||
guy_dev = new guydev_154A_290A ::dev154A; //适用于一般的价签黑白屏
|
||||
#elif (defined(READGUY_DEV_154B) && (READGUY_epd_type==READGUY_DEV_154B))
|
||||
guy_dev = new guydev_154B_270B_290B ::dev154B; //适用于
|
||||
#elif (defined(READGUY_DEV_213A) && (READGUY_epd_type==READGUY_DEV_213A))
|
||||
guy_dev = new guydev_213A ::drv;
|
||||
#elif (defined(READGUY_DEV_266A) && (READGUY_epd_type==READGUY_DEV_266A))
|
||||
guy_dev = new guydev_213B_266A ::dev266A;
|
||||
#elif (defined(READGUY_DEV_213B) && (READGUY_epd_type==READGUY_DEV_213B))
|
||||
guy_dev = new guydev_213B_266A ::dev213B;
|
||||
#elif (defined(READGUY_DEV_290A) && (READGUY_epd_type==READGUY_DEV_290A))
|
||||
guy_dev = new guydev_154A_290A ::dev290A;
|
||||
#elif (defined(READGUY_DEV_290B) && (READGUY_epd_type==READGUY_DEV_290B))
|
||||
guy_dev = new guydev_154B_270B_290B ::dev290B;
|
||||
#elif (defined(READGUY_DEV_420A) && (READGUY_epd_type==READGUY_DEV_420A))
|
||||
guy_dev = new guydev_420A ::drv;
|
||||
#elif (defined(READGUY_DEV_420B) && (READGUY_epd_type==READGUY_DEV_420B))
|
||||
guy_dev = new guydev_420B ::drv;
|
||||
#elif (defined(READGUY_DEV_370A) && (READGUY_epd_type==READGUY_DEV_370A))
|
||||
guy_dev = new guydev_370A ::drv;
|
||||
#elif (defined(MEPD_DEBUG_DISPLAY) && (READGUY_epd_type==MEPD_DEBUG_DISPLAY))
|
||||
guy_dev = new EpdLcdDebug ::drv;
|
||||
#elif (defined(READGUY_DEV_270B) && (READGUY_epd_type==READGUY_DEV_270B))
|
||||
guy_dev = new guydev_154B_270B_290B ::dev270B;
|
||||
#elif (defined(READGUY_DEV_213B3C) && (READGUY_epd_type==READGUY_DEV_213B3C))
|
||||
guy_dev = new guydev_213B_266A ::dev213B3C;
|
||||
#elif (defined(READGUY_DEV_266A3C) && (READGUY_epd_type==READGUY_DEV_266A3C))
|
||||
guy_dev = new guydev_213B_266A ::dev266B3C;
|
||||
|
||||
#elif (defined(READGUY_DEV_154C) && (READGUY_epd_type==READGUY_DEV_154C))
|
||||
guy_dev = new guydev_154C ::drv;
|
||||
#elif (defined(READGUY_DEV_370B) && (READGUY_epd_type==READGUY_DEV_370B))
|
||||
guy_dev = new guydev_370B ::drv;
|
||||
#elif (defined(READGUY_DEV_426A) && (READGUY_epd_type==READGUY_DEV_426A))
|
||||
guy_dev = new guydev_426A ::drv;
|
||||
#elif (defined(READGUY_DEV_583A) && (READGUY_epd_type==READGUY_DEV_583A))
|
||||
guy_dev = new guydev_583A ::drv;
|
||||
#elif (defined(READGUY_DEV_583B) && (READGUY_epd_type==READGUY_DEV_583B))
|
||||
guy_dev = new guydev_583B ::drv;
|
||||
#elif (defined(READGUY_DEV_750A) && (READGUY_epd_type==READGUY_DEV_750A))
|
||||
guy_dev = new guydev_750A ::drv;
|
||||
#elif (defined(READGUY_DEV_1020A) && (READGUY_epd_type==READGUY_DEV_1020A))
|
||||
guy_dev = new guydev_1020A ::drv;
|
||||
#endif
|
||||
//添加新屏幕型号 add displays here
|
||||
#endif
|
||||
#if (defined(ESP8266))
|
||||
SPI.begin();
|
||||
SPI.setFrequency(ESP8266_SPI_FREQUENCY); ///< 1MHz
|
||||
@@ -172,7 +284,7 @@ uint8_t ReadguyDriver::checkEpdDriver(){
|
||||
Serial.println(F("[Guy SPI] drvBase Init OK"));
|
||||
return READGUY_epd_type;
|
||||
}
|
||||
void ReadguyDriver::setEpdDriver(bool initepd/* ,int g_width,int g_height */){
|
||||
void ReadguyDriver::setEpdDriver(bool initepd, bool initGFX){
|
||||
guy_dev->spi_tr_release = in_release;
|
||||
guy_dev->spi_tr_press = in_press;
|
||||
if(initepd) guy_dev->drv_init(); //初始化epd驱动层
|
||||
@@ -181,21 +293,23 @@ void ReadguyDriver::setEpdDriver(bool initepd/* ,int g_width,int g_height */){
|
||||
//if(g_height) guy_height = g_height;
|
||||
//else guy_height = guy_dev->drv_height();
|
||||
//以下依赖于你的图形驱动
|
||||
setColorDepth(1); //单色模式
|
||||
createPalette(); //初始化颜色系统
|
||||
Serial.printf_P(PSTR("[Guy EPD] EPD init OK: w: %d, h: %d\n"),guy_dev->drv_width(),guy_dev->drv_height());
|
||||
//创建画布. 根据LovyanGFX的特性, 如果以前有画布会自动重新生成新画布
|
||||
//此外, 即使画布宽度不是8的倍数(如2.13寸单色),也支持自动补全8的倍数 ( 250x122 => 250x128 )
|
||||
//为了保证图片显示功能的正常使用, 高度也必须是8的倍数.
|
||||
createSprite(guy_dev->drv_width(),guy_dev->drv_height());
|
||||
//这里发现如果用自定义的内存分配方式会更好一些. 不会导致返回的height不对. 但是因为LovyanGFX库未更新 暂时不能这么用.
|
||||
//setRotation(1); //旋转之后操作更方便
|
||||
setRotation(0);
|
||||
setFont(&fonts::Font0);
|
||||
setCursor(0,0);
|
||||
setTextColor(0);
|
||||
fillScreen(1); //开始先全屏白色
|
||||
if(initGFX){
|
||||
setColorDepth(1); //单色模式
|
||||
createPalette(); //初始化颜色系统
|
||||
//创建画布. 根据LovyanGFX的特性, 如果以前有画布会自动重新生成新画布
|
||||
//此外, 即使画布宽度不是8的倍数(如2.13寸单色),也支持自动补全8的倍数 ( 250x122 => 250x128 )
|
||||
//为了保证图片显示功能的正常使用, 高度也必须是8的倍数.
|
||||
createSprite(guy_dev->drv_width(),guy_dev->drv_height());
|
||||
//这里发现如果用自定义的内存分配方式会更好一些. 不会导致返回的height不对. 但是因为LovyanGFX库未更新 暂时不能这么用.
|
||||
setRotation(0); //默认的旋转方向就是0咯
|
||||
setFont(&fonts::Font0);
|
||||
setCursor(0,0);
|
||||
setTextColor(0);
|
||||
fillScreen(1); //开始先全屏白色
|
||||
}
|
||||
Serial.printf_P(PSTR("[Guy EPD] EPD init OK(%d): w: %d, h: %d\n"),guy_dev->drv_ID(),guy_dev->drv_width(),guy_dev->drv_height());
|
||||
}
|
||||
#ifdef READGUY_ENABLE_SD
|
||||
bool ReadguyDriver::setSDcardDriver(){
|
||||
/*重要信息: 有些引脚冲突是难以避免的, 比如8266 尤其需要重写这部分代码
|
||||
对于esp32也要注意这个引脚是否是一个合法的引脚
|
||||
@@ -236,6 +350,17 @@ bool ReadguyDriver::setSDcardDriver(){
|
||||
}
|
||||
return READGUY_sd_ok;
|
||||
}
|
||||
#else
|
||||
bool ReadguyDriver::setSDcardDriver(){
|
||||
READGUY_sd_ok=0;
|
||||
#ifdef READGUY_USE_LITTLEFS
|
||||
LittleFS.begin();
|
||||
#else
|
||||
SPIFFS.begin();
|
||||
#endif
|
||||
return false;
|
||||
}
|
||||
#endif
|
||||
void ReadguyDriver::setButtonDriver(){
|
||||
if(READGUY_btn1) { //初始化按键. 注意高电平触发的引脚在初始化时要设置为下拉
|
||||
int8_t btn_pin=abs(READGUY_btn1)-1;
|
||||
@@ -289,11 +414,11 @@ void ReadguyDriver::setButtonDriver(){
|
||||
btn_rd[1].setLongRepeatMode(0);
|
||||
}
|
||||
else if(READGUY_buttons==3){
|
||||
btn_rd[0].long_press_ms = 150; //不识别双击三击, 只有按一下或者长按, 并且开启连按
|
||||
btn_rd[0].long_press_ms = 50; //不识别双击三击, 只有按一下或者长按, 并且开启连按
|
||||
//btn_rd[0].setLongRepeatMode(1);
|
||||
btn_rd[1].setMultiBtn(1); //设置为多个按钮,不识别双击或三击
|
||||
btn_rd[1].setLongRepeatMode(0);
|
||||
btn_rd[2].long_press_ms = 1; //不识别双击三击, 只有按一下或者长按, 并且开启连按
|
||||
btn_rd[2].long_press_ms = 50; //不识别双击三击, 只有按一下或者长按, 并且开启连按
|
||||
btn_rd[2].setLongRepeatMode(1);
|
||||
}
|
||||
#ifdef ESP8266 //对于esp8266, 需要注册到ticker. 这是因为没freertos.
|
||||
@@ -343,6 +468,7 @@ void ReadguyDriver::setButtonDriver(){
|
||||
}
|
||||
} //关于按键策略, 我们在此使用多个Button2的类, 然后在一个task共享变量来确定上一个按键状态
|
||||
}
|
||||
#ifdef READGUY_ENABLE_SD
|
||||
fs::FS &ReadguyDriver::guyFS(uint8_t initSD){
|
||||
if(initSD==2 || (!READGUY_sd_ok && initSD)) setSDcardDriver();
|
||||
if(READGUY_sd_ok){
|
||||
@@ -358,6 +484,16 @@ fs::FS &ReadguyDriver::guyFS(uint8_t initSD){
|
||||
return SPIFFS;
|
||||
#endif
|
||||
}
|
||||
#else
|
||||
fs::FS &ReadguyDriver::guyFS(uint8_t initSD){
|
||||
(void)initSD; //avoid GCC warning
|
||||
#ifdef READGUY_USE_LITTLEFS
|
||||
return LittleFS;
|
||||
#else
|
||||
return SPIFFS;
|
||||
#endif
|
||||
}
|
||||
#endif
|
||||
void ReadguyDriver::setBright(int d){
|
||||
if(currentBright>=0 && d>=0 && d<=255){
|
||||
currentBright=d;
|
||||
@@ -440,8 +576,7 @@ void ReadguyDriver::sleepEPD(){
|
||||
if(READGUY_cali==127) guy_dev->drv_sleep();
|
||||
}
|
||||
|
||||
#if (!defined(DYNAMIC_PIN_SETTINGS)) //do nothing here.
|
||||
#elif (defined(INDEV_DEBUG))
|
||||
#if (defined(INDEV_DEBUG))
|
||||
void ReadguyDriver::nvs_init(){
|
||||
}
|
||||
void ReadguyDriver::nvs_deinit(){
|
||||
@@ -461,12 +596,19 @@ void ReadguyDriver::nvs_deinit(){
|
||||
}
|
||||
bool ReadguyDriver::nvs_read(){
|
||||
char s[8];
|
||||
for(unsigned int i=0;i<sizeof(config_data)+8;i++){
|
||||
for(unsigned int i=0;i<
|
||||
#ifdef DYNAMIC_PIN_SETTINGS
|
||||
sizeof(config_data)+
|
||||
#endif
|
||||
8;i++){
|
||||
int8_t rd=(int8_t)EEPROM.read(2+i);
|
||||
#ifdef DYNAMIC_PIN_SETTINGS
|
||||
if(i>=8) config_data[i-8] = rd;
|
||||
else s[i]=(char)rd;
|
||||
else
|
||||
#endif
|
||||
s[i]=(char)rd;
|
||||
}
|
||||
Serial.printf("[Guy NVS] Get NVS...%d\n", config_data[0]);
|
||||
Serial.printf("[Guy NVS] Get EEPROM...%d\n", config_data[0]);
|
||||
return !(strcmp_P(s,projname));
|
||||
}
|
||||
void ReadguyDriver::nvs_write(){
|
||||
@@ -483,6 +625,7 @@ void ReadguyDriver::nvs_deinit(){
|
||||
}
|
||||
bool ReadguyDriver::nvs_read(){ //此处需要处理一些有关I2C的内容
|
||||
if(!nvsData.isKey(tagname)) return 0; //没有这个键值
|
||||
#ifdef DYNAMIC_PIN_SETTINGS
|
||||
size_t len=nvsData.getBytes(tagname,config_data,sizeof(config_data)); //读取的数据长度
|
||||
/*if(len<sizeof(config_data)){ //旧版本格式无法获取I2C相关数据, 设置为-1.
|
||||
for(int i=sizeof(config_data)-1;i>=15;i--) //使用新版本格式来存储相关数据
|
||||
@@ -492,6 +635,9 @@ bool ReadguyDriver::nvs_read(){ //此处需要处理一些有关I2C的内容
|
||||
nvsData.putBytes(tagname,config_data,sizeof(config_data)); //用新版本格式保存
|
||||
}*/
|
||||
return len==sizeof(config_data);
|
||||
#else
|
||||
return 1;
|
||||
#endif
|
||||
}
|
||||
void ReadguyDriver::nvs_write(){
|
||||
if(nvsData.isKey(tagname)) nvsData.remove(tagname);
|
||||
|
||||
Reference in New Issue
Block a user